fbpx

Straight and Curved Tube Finishing

ML planetary system is suitable for straight and curved tubes finishing. In this operation the tube is not spinning since the abrasive belts rotate around the tube while this is safely transported by the feeding systems, guaranteeing low vibration.

By removing the feeding units these machines can process curved tubes manually. The operator simply guides the tube through the machine while the abrasive planetary system performs the finishing in the complete diameter of the tube.

Ø 50mm

ML50

– Narrow and flexible abrasives
– Very tight radii in small diameter tubes
– Manual feed

Ø 75mm

ML75

– Narrow and flexible abrasives
– Difficult curves finishing
– Manual or automatic feed

Ø 100mm

ML100

– Abrasive belts 50mm width
– Wide curves finishing
– Manual or automatic feed

Square Tube Finishing

Abrasive Belt & Brush

Rectangular tube and flat bar surface finishing machines up to three stations, combining abrasive belt with contact roller and abrasive brush.

The contact roller applies pressure in the abrasive belt to allow it to grind the flat surface, remove scratches and polishing the tube surface uniformly. The abrasive brush creates smooth finishing both in tubes and flat bars.

FG through-feed tube finishing machines operate normally in one side of the rectangular tube/flat bar only, but double-sided tube polishing machines are also available for higher productivity.

capacities

Wet Operation

These machines work with water cooling system in order to avoid overheating of the tubes and to reduce the risks associated with processing different metals and potentially explosive dusts.

FGW machines can be produced up to 6 finishing stations for one side of the tube surface. These tube and bar polishing machines are also produced in two and even four sides design, performing the surface finishing in 2 or 1 single step.

capacities

Abrasive Belt & Brush

Rectangular tube and flat bar surface finishing machines up to three stations, combining abrasive belt with contact roller and abrasive brush.

The contact roller applies pressure in the abrasive belt to allow it to grind the flat surface, remove scratches and polishing the tube surface uniformly. The abrasive brush creates smooth finishing both in tubes and flat bars.

FG through-feed tube finishing machines operate normally in one side of the rectangular tube/flat bar only, but double-sided tube polishing machines are also available for higher productivity.

Wet Operation

These machines work with water cooling system in order to avoid overheating of the tubes and to reduce the risks associated with processing different metals and potentially explosive dusts.

FGW machines can be produced up to 6 finishing stations for one side of the tube surface. These tube and bar polishing machines are also produced in two and even four sides design, performing the surface finishing in 2 or 1 single step.

capacities
capacities

Round Tube
Mirror Polishing

High quality mirror polishing in stainless steel, copper or aluminum tubes can be required in different industries. NS Máquinas developed different mirror polishing systems which operate with polishing wheels to guarantee a high gloss effect on the tubes surface, whether in round or rectangular tubes or flat bars.

Straight and Curved Tube Mirror Polishing

MP100

High gloss tube polishing, low vibration and possibility to operate straight and curved tubes up to Ø114mm are some of the main features of MP100 round tube mirror polishing machine. The planetary polishing system of MP100 consists in three polishing wheels rotating around the tube while it is transported automatically through the machine.

Centreless Mirror Polishing

RC200

Flexible tube polishing and finishing machines which operate with interchangeable abrasive belt and buffing wheel, allowing different types of finishing in a single station machine.

RC are centreless polishing machines. Tube is spinning and passing through a stationary finishing or polishing station. High diameter flexibility with solutions up to Ø315mm.

High Quality Mirror Polishing

PC70 2P

Perfect mirror polishing by clamping the tube in each extremity and moving the double polishing station along its length.

Developed for round, square and rectangular tubes, these PC70 polishing machines operate automatically with pre-defined cycles.

Straight and Curved Tube Mirror Polishing

MP100

Centreless Mirror Polishing

RC200

High Quality Mirror Polishing

PC70 2P

High gloss tube polishing, low vibration and possibility to operate straight and curved tubes up to Ø114mm are some of the main features of MP100 round tube mirror polishing machine. The planetary polishing system of MP100 consists in three polishing wheels rotating around the tube while it is transported automatically through the machine.

Flexible tube polishing and finishing machines which operate with interchangeable abrasive belt and buffing wheel, allowing different types of finishing in a single station machine.

RC are centreless polishing machines. Tube is spinning and passing through a stationary finishing or polishing station. High diameter flexibility with solutions up to Ø315mm.

Perfect mirror polishing by clamping the tube in each extremity and moving the double polishing station along its length.

Developed for round, square and rectangular tubes, these PC70 polishing machines operate automatically with pre-defined cycles.

Square Tube and Flat Bars Mirror Polishing

Through-Feed Mirror Polishing

PP220 2K

Two oscillating polishing wheels working on surface of the rectangular tubes and bars with capacity up to 220mm width.

High Quality Mirror Polishing

PC70 2P

Perfect mirror polishing by clamping the tube in each extremity and moving the double polishing station along its length.

Developed for round, square and rectangular tubes, these PC70 polishing machines operate automatically with pre-defined cycles.

Equipment

  • MP100

    Максимум Ø114 мм
    Прямые и изогнутые трубы
    Круглые трубы

     

    Прямые и изогнутые круглые трубки до Ø114 для зеркальной полировки с максимальной гибкостью и качеством.

  • AW

    До 11 кВт
    11800 м3/ч
    Мокрая обработка

     

    Пылеуловители с водой циклонного типа

  • AS400

    До 4 кВт
    4000 м3/ч
    Сухая обработка

     

    Пылеуловитель с эффективностью фильтрации 99,9%.

  • AS200

    До 2.2 кВт
    2280 м3/ч
    Сухая обработка

     

    Пылеуловитель с эффективностью фильтрации 99,9%.

  • A

    До 5.5 кВт
    6800 м3/ч
    Сухая обработка

     

    Простые и экономичные пылеуловители с фильтровальными мешками.

  • RC200+RC250

    Максимум Ø250 мм
    Прямые трубы
    Бесцентровая система

     

    Обработка круглых труб и зеркальная полировка в одном многофункциональном станке.

  • FG330

    Максимальная ширина 330 мм
    Сухая финишная обработка
    1-3 станции

     

    Большая возможность обработки для прямоугольных труб и прутков с шириной до 330 мм.

  • FG220

    Максимальная ширина 220 мм
    Сухая финишная обработка
    1-3 станции

     

    Профессиональная финишная обработка прямоугольных труб и прутков шириной до 220 мм.

  • FGW170

    Максимальная ширина 170 мм
    Мокрая финишная обработка
    1-4 станции

     

    Профессиональная финишная обработка прямоугольных труб и прутков шириной до 170 мм.

  • FG170

    Максимальная ширина 170 мм
    Сухая обработка
    1-3 станции

     

    Профессиональная обработка прямоугольных труб и прутков шириной до 170 мм.

  • FC120

    Максимальная ширина 120 мм
    Сухая обработка
    1-2 станции

     

    Идеально подходит для прямоугольных труб и прутков с шириной до 120 мм.

  • ML75

    Максимум Ø76 мм
    Прямые и изогнутые трубы
    1 станция

     

    Идеально подходит для полировки изогнутых круглых труб с небольшим радиусом и диаметром до 76 мм.

  • ML50

    Максимум Ø50 мм
    Изогнутые трубы
    1 станция

     

    Идеально подходит для полировки изогнутых круглых труб с небольшим радиусом и диаметром до 50 мм.

  • MLW100

    Maксимум Ø 114 мм
    Прямые и изогнутые трубы
    1 станция

     

    Прямые и изогнутые круглые трубы с мокрой обработкой до Ø144 мм с максимальной гибкостью и подходом.

  • ML100

    Maксимум Ø 114мм
    Прямые и трубы с изгибом
    1 станция

    <

    Прямые и круглые трубы с изгибом до Ø144 мм с максимальной гибкостью и постоянством.

Contact us